4脚踏式开关操作，控制刀头工作行程，简便、省力、高效、安全。 5离合控制，裁切力度大，其他机型无法比拟。 6用于笔记本，精装书，纸张、纸板、PVC.包装袋,软包装,吊牌等多种软性材料的圆角切割。是制作相册、菜谱、影册、标书、商标等印后加工的配套设备。脚踩脚踏开关，离合器带动圆角冲下切角，操作简便省力高效。厂家直销（温州旭日印刷机械有限公司），一级制造商,生产,售后,品质服务20年。
我们产品基本上是木箱或是木框包装。 在客户满意度和忠诚度方面取得了***的口碑。江西烟盒SJQ平角圆角切角机哪家好
Δ注意事项matters needing attention:
一、 工作期间注意力集中，严格遵守设备操作规程，做到安全作业。
二，调整设备前首先切断电源。
三、根据产品规格的尺寸要求，进行精确调整，调整时需使用**工具，小心仔细，注意安全。
First, pay attention during the work, strictly observe the equipment operating rules, to achieve safe operations.
Second, cut off the power before adjusting the equipment.
Third, according to the size requirements of the product specifications, make precise adjustments. When adjusting, use special tools, be careful and pay attention to safety. 江苏笔记本SJQ平角圆角切角机质量保障不断优化产品结构，精心铸 造产品质量。
PJQ、SJQ型切角机，它的结构精细紧凑，操作方便简易，性能稳定可靠。
工作时，先根据待切工件的大小，通过左右横向螺杆、横向定位滑块调好两个燕尾导向座的距离，将工件放到工作台上，并使后边沿靠到纵向定位块的前面，再由横向定位滑块将工件的横向锁定。
启动电机通减速轮组带动大飞轮、偏心轮转动，当偏心轮的大半径向下转动时，连杆拉动下横梁、导柱、上横梁向下运动，上横梁通过切刀撑杆推动切刀总成沿燕尾导向座下滑动对工件切割。切割完成后恰好偏心轮的大半径向上转动，连杆推动下横梁、导柱、上横梁向上运动，上横梁通过切刀撑杆拉动切刀总成沿燕尾导向座上滑动复位。
用户在收到机器后，应检查机器是否完好无损。然后安装机器。底脚螺丝位置尺寸如下图，也可以不装底脚螺丝，将机器置于水泥地上，比较好于底座下垫已布垫。以免使用过程中机器移动。
After receiving the machine, the user should check whether the machine is intact. Then install the machine. The size of the bottom screw position is as shown in the figure below. It is also possible to place the machine on the cement floor without mounting the bottom screw. It is best to pad the bottom of the base. To prevent the machine from moving during use. 动作快捷准确，待料时间短。
试车Test run在机器安装好后，在接通电源试车，试车前应将各注油孔、滑动面、，注入润滑油，开机前用手扳动偏心轮(图(2)中3)，使切刀做一、两次循环运动，检查机器是否正常，电机转动方向应与偏心轮上箭头所指方向相同，否则裁切时会导致机器非正常损坏。可打开机器左侧小门，观察飞轮转向（图（2）中11）是否与偏心轮上箭头所指方向一致。
After the machine is installed, before the power supply test is connected, each injection hole, sliding surface, and lubricating oil should be injected before the test, and the eccentric wheel should be pulled by hand before starting(Figure(2) in 3). Make the cutter do one or two cycles of movement, check whether the machine is normal, the direction of motor rotation should be the same as the direction indicated by the arrow on the center wheel, otherwise the cutting will cause abnormal damage to the machine. The small door on the left side of the machine can be opened to see whether the flywheel steering(11 in Figure(2)) is consistent with the direction indicated by the arrow on the center wheel. 多年来，我厂致力于切角机系列的生产和开发。上海护卡膜SJQ平角圆角切角机优势
专注印刷机械多年，经验丰富。江西烟盒SJQ平角圆角切角机哪家好
本机由机座、机头、减速箱、工作台、切角刀、拖板等零部件组成。
电机通过减速箱减速后，带动飞轮旋转，当扳下操作手柄（图（2）中14）或踩下踏板（图（2）中19）时，开关座（12）即与飞轮（11）啮合，从而使偏心轮（3）转动，再通过连杆（2）带动切角刀（15）作上下裁切运动。
This machine is made up of parts and components such as machine seat, machine head, speed reduction box, worktable, cutter and towing board.
After the motor decelerates through the speed reducer, it drives the flywheel to rotate. When the handle is pulled down(14 in Figure 2) or the pedal is stepped down(19 in Figure 2), the switch seat(12) is engaged with the flywheel(11)., In this way, the eccentric wheel(3) is rotated, and then the cutting cutter(15) is driven by the connecting rod(2) for up and down cutting motion. 江西烟盒SJQ平角圆角切角机哪家好
温州市旭日印刷机械有限公司位于梧田镇辉煌路9号。旭日印刷机械致力于为客户提供良好的冲切抹角机，切角机，挖月机，压紧机，一切以用户需求为中心，深受广大客户的欢迎。公司秉持诚信为本的经营理念，在机械及行业设备深耕多年，以技术为先导，以自主产品为重点，发挥人才优势，打造机械及行业设备良好品牌。旭日印刷机械秉承“客户为尊、服务为荣、创意为先、技术为实”的经营理念，全力打造公司的重点竞争力。
